| Saw | Pivot Style, Miter Arm, Horizontal Band Saw |
| Saw Capacity | 22” W x 16" H |
| Miter | 15” W x 16" H @ 45˚ (L) (Miter in one direction only) |
| Arm Miter | Release the camlock and move the saw head to the desired position and engage the camlock to lock the arm into place. |
| Arm Lift | Powered from control console. |
| Blade Size | 1-1/4” x 16’0” x .042” THK |
| Blade Drive | 7.5 HP, 220V (25 amps)/3PH or 440V (13 amps)/3PH Electrical Motor Requirement. 220V or 440V AC to be specified by the customer at the time of order. 1800 rpm, ball bearing TFC (***The customer must ground this saw at the machine with an earth ground rod installed prior to installation for the warranty to be in effect.***) |
| Blade Speed | Infinitely variable speed drive controlled through a variable frequency controller and speed is changed from LED readout on console. |
| Air Requirements | 85 PSI, 3 – 5 CFM, equipped with air filter/lubricator |
| Operator Control | Control Console is located in an Easy View style control on a gooseneck mount. The Control Console and gooseneck can each be pivoted for operator convenience. Saw may be operated in semi-automatic mode or fully automatic mode. |
| Automatic 0-24” Stroke Bar-Feed (4 Indexes) | Automatic floating (self-adjusting) shuttle vise feed system with additional rollers to prevent binding of “crooked” and distorted material. The table is 6’ long with a 0-24” feed stroke. |
| Discharge Table | 24” Solid Discharge Support – 10” Wide |
| Adjustable Main Vise | Main-clamping vise is air powered and non-cocking. |
| Vise Clamping Pressure | The operator controls the variable vise pressure, adjustable to clamp various metals. |
| Cutting Pressure | Adjustable cutting pressure/force to control the weight to be placed on the teeth of the blade |
| Cutting Rate | Adjustable to regulate the saw arm traverse rate. This is a necessary feature to cut tubing at high rates without losing saw teeth. |
| Carbide Blade Guides | Side and back carbides are flat for maximum blade support. |
| Blade Chip Brush | Powered brush driven by an assembly mounted on the drive wheel removes chips that may become lodged in the blade gullets. |
| Hold-Down Fixtures | Two each hold down fixtures that mount one on the main vise and one on the shuttle vise for use when cutting more than one piece at a time. |
| Feed Selector and Parts Selector/Counter | Use the Feed Selector to select the number of times the bar-feed will index when cutting parts longer than 24 inches. Use the Parts Selector/Counter to select the number of parts that will be cut. The counter will count down the parts as each one is cut. |
| Built-In Coolant System | Machine is set up for flood-style coolant system with coolant dispensed through the guide arms. The saw is fully panned to return coolant to the tank. |
| Wash-Down Hose | A cutting fluid clean-up hose is provided for machine wash down. |
| Cut Watcher® System | A system that monitors the cut for squareness to a pre-set deviation value. The system shuts down the saw when the pre-set value is exceeded. This is a must option for production cutting. (PATENT: 5,070,751) |
| Blade Break Switch | Saw will automatically shut off if the blade breaks. |
| Out-of-Stock Switch | The saw shuts off when the automatic feed system is out of stock, or when the pre-determined number of pieces has been cut. |
| Safety Guards | Machine is equipped with blade guards and awareness barriers for safety purposes. |
Our knowledgeable staff will assist you with all of you questions.
Contact Us
1287 W Ave.
Ames, IA 50014
Toll Free: 800-237-6330
Office: 515-233-6330
Fax: 515-232-9411
Used Machinery
New Machinery
Precision Rigging
Precision Finishing
SMC Auctions
About Us
Contact Us
© 2024 Smith Machinery Company, Inc.
