SPECIFICATIONS:
PUNCHING -------------------- 13/16 in DIA THROUGH 3/4 in PLATE
THROAT DEPTH -------------------------------5 in
OPEN HEIGHT --------------------------------11-1/2 in
CLOSED HEIGHT W/O DIE BLOCK ----------------7-3/4 in
STROKE LENGTH ------------------------------3-3/4 in
ROUND BAR SHEAR (WITH OPTIONAL KNIVES)----- 1/4 in THROUGH 13/8 in
SQUARE BAR SHEAR (WITH OPTIONAL KNIVES)---- 1/2 in THROUGH 1 in
PLATE SHEAR ----------------------13 in X1/4 in , 10 in X1/2 in , 6 in X3/4 in
ANGLE SHEAR --------------------------------3 in X 3 in X 3/8 in
COPING/NOTCHING ----------------------------2 1/4 in X 3 in X1/4 in
SPEED --------------------------------------28 STROKES/MIN @ 1/2 in STROKE
WORK STATION HEIGHT (APPROX)----------------42 in
FLUID CAPACITY -----------------------------12 GALLONS
MOTOR --------------------------------------3 HP
WEIGHT -------------------------------------1,700 LBS
FEATURES:
1. Urethane Stripper Attachment- keeps material flat through the punching process, eliminating distortion. The shorter required stroke gives you a faster punching cycle.
2. Mechanical Shear Hold-downs- clamps material at change of material thickness. Part movement is eliminated by clamping the part throughout the entire shearing cycle.
3. Visibility- a direct line of sight over the hold down bar allows the operator to easily and accurately line up cuts to the shear blades.
4. Flat Bar Shear- the low rake angle shear design results in flatter and higher quality sheared parts. Shear blades have four useable edges giving you a longer life and less expensive blades.
5. Angle Shear- the square upper angle knife has four cutting radiuses to better fit the angle being sheared, giving you lower distortion and a higher quality cut.
6. Coper Notcher- the low rake angle blade keeps part flat and under control during notching.
EQUIPPED WITH:
Mechanical Hold Down
Coupling Wrench
Punch Holder, Urethane Stripper, & Die
Block
1/2 inch Allen Wrench
Set of Angle Knives
Foot Switch
Set of Coper Knives
Set of 13 inch Plate Shear Knives
Instruction/Parts Book
MACHINE IS SHIPPED TOTALLY WIRED THROUGH THE ELECTRICAL ENCLOSURE BOX. IT HAS BEEN LEFT TO THE PURCHASER ftS DISCRETION WHETHER TO WIRE DIRECT TO A DISCONNECT OR TO INSTALL A CORD AND PLUG FOR MOBILITY.
MACHINE REQUIRES MOBILE DTE-13M(OR EQUIVALENT) HYDRAULIC OIL OPTIONAL
OPTIONAL FEATURES:
3' Backgauge, manual ------------------------- $1,995.00
6' Backgauge, manual -------------------------- $2,195.00
9' Backgauge w/ leg, manual ------------------- $2,595.00
Punching Quick Set Plate/Angle Gauging Table -- $1,695.00
5' Quick Set Table Extension Attachment ------- $1,095.00
10' Quick Set Table Extension Attachment------ -$1,495.00
6 inch Bending attachment ----------$645.00
12 inch Bending attachment ---------$1,095.00
Channel Die Block ------------------------------$795.00
1-9/16" inch Oversize Punch Attachment (Urethane) ----$1,895.00
28XX Punch Attachment 2 inch -------------------$1,995.00
28XX Punch Attachment 3 inch ------------------ $2,045.00
Pipe Notching Die Holder -----------------------$265.00
Fig. DH Pipe Notching Striker ------------------$38.00
3/4 in Schedule 40 Pipe Notching Die -------------$432.00
1 inch Schedule 40 Pipe Notching Die ---------------$432.00
1-1/4 inch Schedule 40 Pipe Notching Die -----------$432.00
1-1/2 inch Schedule 40 Pipe Notching Die -----------$432.00
2 inch Schedule 40 Pipe Notching Die ---------------$526.00
Single Phase Motor (Add to machine price)-------$450.00
10 Piece Punch & Die Set -----------------------$305.45
5 Piece Punch & Die Set ------------------------$152.95
Chip Bucket ------------------------------------$81.35
Copper Table Guides, set of 3 ------------------$135.00
DELIVERY:
SUBJECT TO STOCK